PRODUCT INFORMATION
This is a highly efficient general purpose cleaning solvent.
It is ideal for the efficient and speedy removal of stains, coatings, printing inks or deposits of oil, grease or dirt. It is a product of low toxicity, leaves no residue and does not cause corrosion of metals. It is safe to use on most plastics or fibres and it quickly evaporates (we advise a test on a small sample if in doubt). It is suitable for cleaning most electrical apparatus, installations and delicate instruments leaving no residue.

DIRECTIONS
Spray from a distance of 15-30cm. The product will evaporate rapidly. Any excess should be wiped off where necessary.

PRODUCT
ARROW 38 CLEAR ACRYLIC LACQUER

PRODUCT INFORMATION
This is a fast drying acrylic coating, having a wide range of uses, including sealing of printed circuitry in the electronics industry, metal and paintwork overlacquering, and as a waterproofing coating for maps and technical documents.
It sprays to give a fast drying, tough, clear acrylic coating. The dried coating is non-yellowing and resistant to mild acid and alkali attack.

Dielectric Properties:
(Determined on a 30 micron fully dried film at 20 Deg.C, 50% R.H.)
1. Dielectric Constant : 50 Hz - 10,000 Hz = 3.38
2. Volume Resistivity : 15 - 400 Volts = 1 x 10 (to the power 15) ohm-cm
3. Dielectric Breakdown : 42.6 k.volts/mm

DIRECTIONS
Spray a thin even coat onto a clean dry surface from a distance of 25 to 30cm. The surface will be touch dry within 20 minutes. Repeat as necessary leaving 20 minutes drying time between coats.

PRODUCT
ARO SOLV 400ml EASY CLEAN SOLVENT

PRODUCT INFORMATION
This is a highly efficient general purpose cleaning solvent fitted with a unique spray through cap system.
It is ideal for the efficient and speedy removal of stains, coatings, printing inks or deposits of oil, grease or dirt. It is a product of low toxicity and leaves no residue. It is safe to use on most plastics or fibres and it quickly evaporates (we advise a test on a small sample if in doubt). It is suitable for cleaning most electrical apparatus, installations and delicate instruments leaving no residue.

DIRECTIONS
Spray from a distance of 15-30cm. The product will evaporate rapidly. Any excess should be wiped off where necessary.

PRODUCT
ARROW 37 ANTI-STATIC

PRODUCT INFORMATION
This is a water-based aerosol spray which helps to reduce static electricity, dirt and dust build-up.
This anti-static compound reduces deposits of dust, dirt and problems of static electricity. Ideal for use on textile machinery, paper converting and folding machines, plastic packaging and bag making equipment, laundry or anywhere where static presents problems or is undesirable.

DIRECTIONS
On hard surfaces: Spray onto surface and rub over with a soft dry cloth.
On fabrics: Spray onto surface and allow to dry.

PRODUCT
ARROW 76 PRESSURISED AIR DUSTER (HFA 134a)

PRODUCT INFORMATION
A high pressure propellant aerosol for removing dust from hard to reach places.
It is ideal for removing dust from most electrical equipment including keyboards, printers, PCBs etc.

DIRECTIONS
Spray directly onto the affected area using the extension tube.
Always keep the can in an upright position when spraying to avoid discharging liquefied propellant..

PRODUCT
ARROW 20 CIRCUIT FREEZER

PRODUCT INFORMATION
This is a rapidly evaporating propellant mixture suitable for reducing surface temperatures of electrical components to aid detection of overheating and similar faults. It is also often used to freeze water in small bore pipes to effect a repair avoiding the necessity of system drainage.
Further use can be found as a highly effective chewing gum remover.
Note: Will cause a "cold" burn if in contact with skin tissues.

DIRECTIONS
Spray directly onto affected component using the extension tube.
For chewing gum removal, apply to gum until frozen, then pull or chip away.

PRODUCT
ARROW 56 SILICONE/PTFE LUBRICANT

PRODUCT INFORMATION
This is a high grade lubricant containing silicone, PTFE and dewatering agents.
It is a highly efficient, non-staining, high slip lubricant which was originally developed for use in marine applications. However, the blend of excellent lubricants with extremely efficient dewatering agents make it ideal for use in any industry where wet conditions apply (e.g. bottling plants).

DIRECTIONS
Shake aerosol before use. Hold upright and spray from 15-20cm directly onto the surface to be lubricated. After use, invert the can and press the button for 2 seconds to clear the nozzle.

PRODUCT
ARROW17 VDU CLEANER

PRODUCT INFORMATION
This is an aerosol foam cleaner, solvent-built to improve its cleansing properties. It is an effective cleaner for VDU screens and keyboards, printers, televisions, photocopiers, etc. It is also suitable for most materials used in office furniture and car seats/trim. It sprays to give a contact foam cleanser which collapses on working. Removes a wide range of soils from most fabric and hard surfaces.

DIRECTIONS
Hardware: Do not spray directly onto equipment, chemicals may ingress into electrical parts to cause damage. Spray cleaner onto dampened cloth and wipe over surface to be cleaned. Wipe away any residues with a further clean, damp cloth.
Upholstery: Spray directly onto affected area, allow foam to build and penetrate for a few minutes, wipe off with a damp cloth.